Questions? Call us at (262) 218-2915

Sign Regulations in Pleasure Ridge Park, Kentucky

Pleasure Ridge Park, Kentucky has specific sign regulations covering 76 sign types across 13 zoning districts. Regulated sign types include All Permanent Signs (General), Changing Image Sign (Attached or Freestanding), Moving Sign (Revolving/Rotating). Height restrictions apply. Permits are required for most commercial signs. Use PermitPal to get instant access to the complete regulations.

Data last verified: December 15, 2025

Need the sign code for this address?

PermitPal is an independent research tool for sign companies. We are not the city's permit office.

Sign Regulation Overview for Pleasure Ridge Park, Kentucky

Sample Sign Requirements in Pleasure Ridge Park

Sign TypeMax HeightMax AreaSetback
All Permanent Signs (General)Not listedNot listedNo sign may obstruct required vision clearance triangle at corners: no freestanding sign over 2 ft height within the specified triangle (Section 5.1.7.G). No freestanding sign may be located in or project into the right‑of‑way (8.3.3.B.2). Gasoline pump islands must be set back at least 15 ft from ROW or the applicable district setback, whichever is greater (5.1.7.I). Freestanding business signs may be in required yards if they meet sight‑distance rules (8.3.3.B.7).
Changing Image Sign (Attached or Freestanding)Not listedPortion of sign that may be changing image: 30% of total sign area in Neighborhood, Village, Traditional Neighborhood Form Districts; 60% of total sign area in all other form districts (8.2.1.D.4). Other area limits by sign type and form district still apply.Must also respect general freestanding sign setbacks and 300‑ft spacing from certain resources (residential property and Olmsted parks) per 8.2.1.D.6–8.
Incidental Sign (Including Drive‑through Menu Board)Not listedDrive‑through menu boards: max 40 sq ft each, up to two single‑faced boards (8.3.3.C). Other incidental sign sizes per definition in 8.1.2 (not fully reproduced here).May be located in required yards, subject to sight‑distance rules (8.3.3.C; 8.1.6.A).

* Sample data shown. Actual requirements may vary by zone. Use PermitPal for complete, location-specific regulations.

PermitPal Coverage for Pleasure Ridge ParkFull Coverage

Sign Types Covered

76

  • All Permanent Signs (General)
  • Changing Image Sign (Attached or Freestanding)
  • Moving Sign (Revolving/Rotating)
  • Incidental Sign (Including Drive‑through Menu Board)
  • +2 more types

Zoning Districts

13

Different zoning districts with specific sign regulations

Data Includes

  • Permit requirements
  • Height restrictions
  • Illumination rules

Official Resources for Pleasure Ridge Park

City WebsiteMunicipal Code1 permit application link available

Frequently Asked Questions

In Pleasure Ridge Park, the height limit for Residential Sign – 3+ Family Residential – Freestanding Sign (Arterial ≤4 lanes) in the R-R Rural Residential District (R-R) and other zoning districts is 10 ft (Table 8.3.1). Other zones and sign types can have different limits. Run a code check for an exact address to see the limit that applies there.

Most commercial signs in Pleasure Ridge Park require a permit. From the submission notes on this page: The term "Sign plan" is a defined term in LDC §8.1.2, indicating that sign plans are contemplated by the code, although procedural details are not included in the provided text. Run a code check for an exact address to see the permit requirements for that zone.

Pleasure Ridge Park's sign code covers 76 sign types, including All Permanent Signs (General), Changing Image Sign (Attached or Freestanding), Moving Sign (Revolving/Rotating), and Incidental Sign (Including Drive‑through Menu Board). Most commercial signs need a permit. The ordinance lists 7 exemptions. One of them: Signs listed as exempt within the Land Development Code are not required to submit plans and specifications and are not required to obtain a permit under LMCO §155.02 for erection or alteration (LMCO §155.02(A), (B)). The full list is on this page.

This page doesn't list a single setback distance for signs in Pleasure Ridge Park. The tables on this page quote the ordinance's placement rules for the sign types we sampled. Run a code check for an exact address to see the setback that applies there.

Rules in Pleasure Ridge Park's sign ordinance that cover digital, changing, or flashing signs: All illuminated signs must be non‑flashing and constant in intensity and color, except as specifically allowed for changing image signs under §8.2.1(D) (LDC §8.2.1(B)). Freestanding or attached signs that include changing image signs shall not be located closer than 300 feet to an Olmsted Park boundary or Olmsted Parkway right‑of‑way (LDC §8.2.1(D)(8)). Changing image signs with a rate of change faster than the standard limits require approval from the Planning Commission or designee after review of specified factors (LDC §8.2.1(D)(5)), which serves as a special sign approval process. Run a code check for an exact address to see the full illumination rules for that zone.

AI-Powered Research

Ready to Research Pleasure Ridge Park Sign Permits?

Stop spending hours searching through municipal codes. Enter your address and PermitPal returns the sign rules that apply to your property in Pleasure Ridge Park, Kentucky, with citations from the municipal code.

Need the sign code for this address?

PermitPal is an independent research tool for sign companies. We are not the city's permit office.

No credit card required · Get results in seconds

Pleasure Ridge Park, Kentucky Sign Rules at a Glance

Pleasure Ridge Park, Kentucky regulates 76 sign types across 13 zoning districts. Temporary Signs - Subdivision Construction Sign are capped at 15 ft above ground and 64 sq ft (Sec. 155.22(F)(1)–(3)). Most commercial signs in Pleasure Ridge Park require a permit.

Detailed Sign Ordinance Requirements for Pleasure Ridge Park, Kentucky

Sign Rules by Zoning District in Pleasure Ridge Park (13 zones)

Zoning DistrictSign Types RegulatedMax HeightMax AreaPermit Required
General Regulations For All Zones12For freestanding business signs 200–500 ft from Snyder Freeway ROW: max 20 ft height (155.31(B)).For freestanding business signs 200–500 ft from Snyder Freeway ROW: max 80 sq ft face area, and must also meet the size limits of its zoning district (155.31(B)).Not listed
R-R Rural Residential District (R-R), R-E Residential Estate District (R-E), R-1 Residential Single Family District (R-1), R-2 Residential Single Family District (R-2), R-3 Residential Single Family District (R-3), R-4 Residential Single Family District (R-4), R-5 Residential Single Family District (R-5), U-N Urban Neighborhood District (U-N), R-5A Residential Multi-Family District (R-5A), R-5B Residential Two-Family District (R-5B), R-6 Residential Multi-Family District (R-6), R-7 Residential Multi-Family District (R-7), R-8A Residential Multi-Family District (R-8A), OR Office/Residential District (OR), OR-1 Office/Residential District (OR-1), OR-2 Office/Residential District (OR-2), OR-3 Office/Residential District (OR-3), OTF Office/Tourist Facility (OTF), C-N Neighborhood Commercial District (C-N), C-R Commercial/Residential District (C-R), C-1 Commercial District (C-1), C-2 Commercial District (C-2), C-3 Commercial District (C-3), CM Commercial Manufacturing (CM), EZ-1 Enterprise Zone District (EZ-1), M-1 Industrial District (M-1), M-2 Industrial District (M-2), M-3 Industrial District (M-3), PRO Planned Research/Office Center District (PRO), PEC Planned Employment Center District (PEC), DRO Development Review Overlay (DRO), W-1 Waterfront District (W-1), W-2 Waterfront District (W-2), W-3 Waterfront District (W-3), WRO Waterfront Development Review Overlay District (WRO), PDD Planned Development District (PDD), PVD Planned Village Development District (PVD), PTD Planned Transit Development District (PTD), PRD Planned Residential Development District (PRD), TNZD Traditional Neighborhood Zoning District (TNZD)910 ft (Table 8.3.1).48 sq ft (Table 8.3.1).Not listed
Neighborhood Form District (N)8Below roof line or uppermost portion of parapet wall (Table 8.3.2).300 sq ft total attached sign area per façade (Table 8.3.2).Not listed
Traditional Neighborhood Form District (TN)61 tenant: 4 ft; 2–3 tenants: 6 ft; >4 tenants: 8 ft.Up to 20% of façade area, not to exceed 60 sq ft total (Table 8.3.2 TN, Office/Commercial/Industrial).Not listed
Village Form District (V, VC)51 tenant: 4 ft; 2–3 tenants: 6 ft; >4 tenants: 8 ft.Small façades: ≤5% of façade to 60 sq ft; larger façades: formula values, capped at 300 sq ft (Table 8.3.2 Village).Not listed
Suburban Marketplace Corridor Form District (SMC)51 tenant: 12 ft; 2–3 tenants: 14 ft; >4 tenants: 16 ft.As above; cap 500 sq ft for largest façades.Not listed
Traditional Marketplace Corridor Form District (TMC)51 tenant: 6 ft; 2–3 tenants: 6 ft; >4 tenants: 10 ft.As above; 300 sq ft cap.Not listed
Suburban Workplace Form District (SW)51 tenant: 12 ft; 2–3 tenants: 14 ft; >4 tenants: 16 ft.Cap 750 sq ft.Not listed
Traditional Workplace Form District (TW)51 tenant: 10 ft; 2–3 tenants: 12 ft; >4 tenants: 14 ft.Cap 750 sq ft.Not listed
Campus Form District (C)41 tenant: 6 ft; 2–3 tenants: 8 ft; >4 tenants: 10 ft.Cap 500 sq ft.Not listed
Downtown Form District (DT)2Directory sign: up to 6 ft (8.3.3.B.10.c.i).Up to 750 sq ft for largest façades (with special South Fourth St. rule).Not listed
Town Center Form District (TC)51 tenant: 6 ft; 2–3 tenants: 8 ft; >4 tenants: 10 ft.Cap 500 sq ft.Not listed
Regional Center Form District (RC)51 tenant: 12 ft; 2–3 tenants: 14 ft; >4 tenants: 16 ft.5,000–9,999 sq ft façade: 500 sq ft; 10,000+ façades: 750 sq ft – however table only lists freestanding area/height as 100/24, 120/26, 140/28 for 5,000–9,999; 10,000+ shows blanks; treat 100/24, 120/26, 140/28 as freestanding sign caps per tenant count.Not listed

Zone-by-Zone Sign Requirements in Pleasure Ridge Park(sample of 3 of 13 zones)

General Regulations For All Zones

Sign TypeMax HeightMax AreaMax WidthSetbackSigns AllowedLocationPermit RequiredPremium Details(Illumination, Size Formula, Permit Requirements, Additional Requirements, available with a free PermitPal account)Ordinance Citation
Changing Image Sign (Attached or Freestanding)Not listedPortion of sign that may be changing image: 30% of total sign area in Neighborhood, Village, Traditional Neighborhood Form Districts; 60% of total sign area in all other form districts (8.2.1.D.4). Other area limits by sign type and form district still apply.Not listedMust also respect general freestanding sign setbacks and 300‑ft spacing from certain resources (residential property and Olmsted parks) per 8.2.1.D.6–8.Maximum one changing image sign per property (8.2.1.D.1).Anywhere an attached or freestanding on‑premises sign is allowed, except: must be at least 300 ft from residentially used property or a residential zoning district unless the property is exclusively non‑residential or the changing image is not visible to the residential property; must be at least 300 ft from an Olmsted Park boundary or Olmsted Parkway ROW (8.2.1.D.6–8).Not listedUnlock8.2.1.D–E
Incidental Sign (Including Drive‑through Menu Board)Not listedDrive‑through menu boards: max 40 sq ft each, up to two single‑faced boards (8.3.3.C). Other incidental sign sizes per definition in 8.1.2 (not fully reproduced here).Not listedMay be located in required yards, subject to sight‑distance rules (8.3.3.C; 8.1.6.A).Two single‑faced menu‑board‑type signs allowed per drive‑through facility (8.3.3.C).On‑premises at drive‑through facilities; freestanding incidental signs allowed within required yards (8.3.3.C).Not listedUnlock8.3.3.C; 8.1.2 (definition reference); 8.1.6.A,H
Temporary Sign – Small Freestanding On‑Premises SignMax 4 ft above ground (155.22(A)(2)).Max 12 sq ft per face; max 2 faces (155.22(A)(2)).Not listedMust be outside public right‑of‑way/ROW/easements unless specially permitted; must not obstruct sight lines (155.22(A)(3); 155.23).One small freestanding on‑premises sign per principal non‑residential use (155.22(A)(1)).Only on properties with a principal non‑residential use. Not allowed in public right‑of‑way, interstate/expressway ROW, or public easement without required permits, and even then must be removed when business is closed (155.22(A)(3)). Must not obstruct sight lines for streets, sidewalks or driveways (155.22(A)(3); 155.23).Not listedUnlock155.20; 155.21; 155.22(A); 155.23
Temporary Sign – Temporary Banner SignNot listedAs above; minimum effective cap 60 sq ft unless 50% rule yields larger.Not listedN/A – attached to structures, not freestanding.One temporary banner per premises at a time (155.22(B)).On‑premises, attached flat to permanent structures (building façade, etc.).Not listedUnlock155.20; 155.21; 155.22(B)
Temporary Sign – Temporary Freestanding On‑Premises SignMax 6 ft above ground (155.22(C)(3)).Max 32 sq ft per face; max 2 faces (155.22(C)(3)).Not listedMust be outside public and interstate/expressway ROW and public easements; must not block sight lines (155.23).One temporary freestanding on‑premises sign per property (155.22(C)(1)).Permitted on any property, but not in public or interstate/expressway right‑of‑way or public easement (155.23).Not listedUnlock155.20; 155.21; 155.22(C); 155.23–155.24
Temporary Sign – Window SignNot listedMax 25% of total area of each window where sign is located (155.22(D)(2)).Not listedN/A – interior/attached to façade windows.No explicit numeric limit; constrained by 25%‑of‑window‑area rule.Inside or on windows visible from exterior, for principal non‑residential uses (155.22(D)(1)).Not listedUnlock155.20; 155.22(D)
Temporary Sign – Construction Sign (Individual Contractor)Max 15 ft above ground (155.22(F)(2)).≤12 sq ft per individual contractor sign; alternative joint‑contractor sign ≤64 sq ft (155.22(F)(2)).Not listedMust be outside public/right‑of‑way and must not obstruct sight lines (155.23).One per contractor; or one combined sign for all contractors (155.22(F)(1)–(2)).On property where construction activity is occurring; any zoning district (155.22(F)(1)).Not listedUnlock155.20; 155.21; 155.22(F)(1)–(3)
Temporary Sign – Subdivision Construction Sign≤15 ft above ground (155.22(F)(2)).≤64 sq ft (155.22(F)(2)).Not listedMust comply with 155.23 placement rule (no ROW; no sight obstruction).One subdivision construction sign per dedicated street entrance (155.22(F)(1)).At each dedicated street entrance to subdivision, within building lines.Not listedUnlock155.22(F)(1)–(3)

R-R Rural Residential District (R-R), R-E Residential Estate District (R-E), R-1 Residential Single Family District (R-1), R-2 Residential Single Family District (R-2), R-3 Residential Single Family District (R-3), R-4 Residential Single Family District (R-4), R-5 Residential Single Family District (R-5), U-N Urban Neighborhood District (U-N), R-5A Residential Multi-Family District (R-5A), R-5B Residential Two-Family District (R-5B), R-6 Residential Multi-Family District (R-6), R-7 Residential Multi-Family District (R-7), R-8A Residential Multi-Family District (R-8A), OR Office/Residential District (OR), OR-1 Office/Residential District (OR-1), OR-2 Office/Residential District (OR-2), OR-3 Office/Residential District (OR-3), OTF Office/Tourist Facility (OTF), C-N Neighborhood Commercial District (C-N), C-R Commercial/Residential District (C-R), C-1 Commercial District (C-1), C-2 Commercial District (C-2), C-3 Commercial District (C-3), CM Commercial Manufacturing (CM), EZ-1 Enterprise Zone District (EZ-1), M-1 Industrial District (M-1), M-2 Industrial District (M-2), M-3 Industrial District (M-3), PRO Planned Research/Office Center District (PRO), PEC Planned Employment Center District (PEC), DRO Development Review Overlay (DRO), W-1 Waterfront District (W-1), W-2 Waterfront District (W-2), W-3 Waterfront District (W-3), WRO Waterfront Development Review Overlay District (WRO), PDD Planned Development District (PDD), PVD Planned Village Development District (PVD), PTD Planned Transit Development District (PTD), PRD Planned Residential Development District (PRD), TNZD Traditional Neighborhood Zoning District (TNZD)

Sign TypeMax HeightMax AreaMax WidthSetbackSigns AllowedLocationPermit RequiredPremium Details(Illumination, Size Formula, Permit Requirements, Additional Requirements, available with a free PermitPal account)Ordinance Citation
Residential Sign – 1 or 2 Family (Attached Sign)May not extend above roof line or highest point of parapet wall of building (footnote to Table 8.3.1).1 sq ft sign area (Table 8.3.1, Attached Sign Size).Not listedNot listedOne per lot (Table 8.3.1).On a 1‑ or 2‑family dwelling lot in any zoning district (Table 8.3.1 ‘Form District: NA’).Not listedUnlock8.3.2; Table 8.3.1, row ‘1 or 2 Family Residential’
Residential Sign – 1 or 2 Family (Freestanding Sign)6 ft overall height (Table 8.3.1: ‘1 S.F./6 ft.’).1 sq ft sign face area (Table 8.3.1).Not listedCannot be in/right above right‑of‑way; must not obstruct visibility triangles (5.1.7.G; 8.1.6.A; 8.3.3.B.2).One per residential lot.On the lot of a 1‑ or 2‑family residence, any zoning district.Not listedUnlock8.3.2; Table 8.3.1, ‘1 or 2 Family Residential’
Residential Sign – Subdivision Identification Sign (Freestanding)6 ft height (Table 8.3.1).15 sq ft per sign face (Table 8.3.1). For ‘signature entrance’ walls/fences under Section 4.4.3, each wall/fence may include one 15 sq ft sign face, max two per entrance (text under 8.3.2).Not listedMust comply with general yard and visibility requirements and any special parkway buffers (Table 8.3.3; 5.1.7.G).One per dedicated subdivision entrance; up to two faces if part of signature entrance walls/fences.At each dedicated subdivision entrance (Table 8.3.1; 8.3.2).Not listedUnlock8.3.2 (paragraph after Table 8.3.1); Table 8.3.1 ‘Subdivision Identification Sign’ row; Section 4.4.3 (referenced)
Residential Sign – Fraternities and Sororities (Attached or Freestanding)6 ft for freestanding sign (Table 8.3.1 ‘6 S.F./6 ft.’). Attached sign height limited to below roof line or parapet (footnote).6 sq ft sign area (Table 8.3.1).Not listedFreestanding signs must respect ROW and sight‑distance rules.One per fraternity/sorority property.Any zoning district where a fraternity/sorority residential use exists (Table 8.3.1).Not listedUnlockTable 8.3.1, ‘Fraternities and Sororities’ row
Residential Sign – 3+ Family Residential (Neighborhood/TN/Town Center) – Attached SignAttached signs must not extend above roof line or top of parapet (footnote to Table 8.3.1).Max attached sign area is tied to freestanding allowance per street class (see next row and Note); not separately quantified beyond the table note that attached signs use area maximums from the table and must not extend above roofline/parapet.Not listedNot listedOne per street frontage (Table 8.3.1).On multi‑family residential sites (3+ units) in Neighborhood, Traditional Neighborhood, and Town Center form districts (Table 8.3.1). These multi‑family uses could be mapped to various residential zoning districts but sign limit here is by form district, not zoning district label.Not listedUnlockTable 8.3.1, ‘3 or more Family Residential’ rows; table Note
Residential Sign – 3+ Family Residential (Neighborhood/TN/Town Center) – Freestanding Sign (Local Street)6 ft (Local street) (Table 8.3.1).12 sq ft per sign face (Local street) (Table 8.3.1).Not listedFreestanding sign must comply with ROW/sight‑distance requirements.One per street frontage.Multi‑family residential development in Neighborhood, Traditional Neighborhood, or Town Center Form Districts, on a local street frontage.Not listedUnlockTable 8.3.1, ‘3 or more Family Residential’ – Local
Residential Sign – 3+ Family Residential – Freestanding Sign (Collector Street)6 ft (Table 8.3.1).24 sq ft (Table 8.3.1).Not listedAs above.One per street frontage.As above, but fronting on a collector street.Not listedUnlockTable 8.3.1, ‘3 or more Family Residential’ – Collector
Residential Sign – 3+ Family Residential – Freestanding Sign (Arterial ≤4 lanes)10 ft (Table 8.3.1).48 sq ft (Table 8.3.1).Not listedNot listedOne per street.3+ family residential on arterial street (4 lanes or less).Not listedUnlockTable 8.3.1, ‘3 or more Family Residential’ – Arterial, 4 lanes or less

Neighborhood Form District (N)

Sign TypeMax HeightMax AreaMax WidthSetbackSigns AllowedLocationPermit RequiredPremium Details(Illumination, Size Formula, Permit Requirements, Additional Requirements, available with a free PermitPal account)Ordinance Citation
Attached Sign – Office/Commercial/Industrial (Neighborhood N) – Façade <500 sq ftBelow roof line or uppermost portion of parapet wall (Table 8.3.2).Up to 5% of façade area, not to exceed 150 sq ft total per façade (Table 8.3.2 Neighborhood, first attached row).Not listedMay project up to 18 inches into ROW without special Public Works approval (8.3.3.A.4).Baseline one per façade per first row, but total attached/awning/canopy/marquee signs per façade limited to three per 8.3.3.A.1 (multi‑tenant exceptions).On any building façade for office, commercial, and industrial uses within Neighborhood (N) Form District.Not listedUnlockTable 8.3.2 Neighborhood; 8.3.3.A.1, A.6; 8.2.1.A
Attached Sign – Office/Commercial/Industrial (Neighborhood N) – Façade 500–999 sq ftBelow roof line or parapet.100 sq ft + 0.15 × (façade area – 500 sq ft).Not listedStandard attached sign projection rules (18" max into ROW).Max 3 attached/awning/canopy/marquee signs per façade.Neighborhood (N) Form District office/commercial/industrial façades 500–999 sq ft.Not listedUnlockTable 8.3.2 Neighborhood; 8.3.3.A.1; 8.2.1.A
Attached Sign – Office/Commercial/Industrial (Neighborhood N) – Façade 1,000–3,499 sq ftBelow roof line/parapet.175 sq ft + 0.05 × (façade area – 1,000 sq ft), subject to global 300‑sq‑ft cap in later row for large façades.Not listedNot listedUp to 3 attached signs per façade.Neighborhood (N) Form District façades 1,000–3,499 sq ft.Not listedUnlockTable 8.3.2 Neighborhood – rows ‘1,000–3,499 S.F.’ and ‘3,500 S.F. or greater’; 8.3.3.A.1
Attached Sign – Office/Commercial/Industrial (Neighborhood N) – Façade ≥3,500 sq ftBelow roof line/parapet.300 sq ft total attached sign area per façade (Table 8.3.2).Not listedNot listedUp to 3 attached/awning/canopy/marquee per façade, excluding first‑floor awnings counted separately for number but not for area (8.3.3.A.1).Neighborhood Form District, large façades ≥3,500 sq ft.Not listedUnlockTable 8.3.2 Neighborhood; 8.3.3.A.1; 8.2.1.A
Freestanding Sign – Office/Commercial/Industrial (Neighborhood N) – Local StreetOne‑tenant: 6 ft; 2–3 tenants: 8 ft; >4 tenants: 10 ft.One‑tenant site: 40 sq ft; 2–3 tenants: 60 sq ft; >4 tenants: 80 sq ft (Table 8.3.2 Neighborhood, Local row).Not listedNo minimum setback from ROW if sight‑distance satisfied (8.3.3.B.7), but building on that frontage must be ≥15 ft from ROW to qualify for any freestanding sign (8.3.3.B.6).One per street frontage, with possibility for second if frontage >600 ft (8.3.3.B.3–4).Office, commercial, industrial uses in Neighborhood Form District along local streets.Not listedUnlockTable 8.3.2 Neighborhood (Local); 8.3.3.B.1–4,6–9
Freestanding Sign – Office/Commercial/Industrial (Neighborhood N) – Collector Street1 tenant: 8 ft; 2–3 tenants: 10 ft; >4 tenants: 12 ft.1 tenant: 60 sq ft; 2–3 tenants: 80 sq ft; >4 tenants: 100 sq ft.Not listedAs above.One per street frontage (with 600‑ft frontage exception).Neighborhood Form District office/commercial/industrial uses on collector streets.Not listedUnlockTable 8.3.2 Neighborhood – Collector row; 8.3.3.B
Freestanding Sign – Office/Commercial/Industrial (Neighborhood N) – Arterial (≤4 lanes)1 tenant: 10 ft; 2–3 tenants: 12 ft; >4 tenants: 14 ft.1 tenant: 80 sq ft; 2–3 tenants: 100 sq ft; >4 tenants: 120 sq ft.Not listedAs above.One per street frontage.Neighborhood Form District, arterial street (4 lanes or less).Not listedUnlockTable 8.3.2 Neighborhood – Arterial, 4 lanes or less; 8.3.3.B
Freestanding Sign – Office/Commercial/Industrial (Neighborhood N) – Arterial (>4 lanes)1 tenant: 12 ft; 2–3 tenants: 14 ft; >4 tenants: 16 ft (Table 8.3.2, last row).1 tenant: 80 sq ft; 2–3 tenants: 100 sq ft; >4 tenants: 120 sq ft (from last arterial row, though table shows only height change).Not listedAs above.One per street frontage.Neighborhood Form District on arterials with more than 4 lanes.Not listedUnlockTable 8.3.2 Neighborhood – Arterial, more than 4 lanes; 8.3.3.B

PermitPal covers all 13 zoning districts in Pleasure Ridge Park. Run a code check for your exact address to get the zone that applies to your property and its full sign requirements with a free account: illumination rules, size formulas, and permit requirements for every sign type.

Run a free code check

Prohibited Signs in Pleasure Ridge Park

  • Off-premises/outdoor advertising signs are prohibited except as specifically allowed under Chapter 4, Part 3 (LDC §8.1.6(C)).
  • No sign shall be constructed and placed so as to obstruct sight lines for persons using streets, pedestrian rights-of-way, and driveways (LDC §8.1.6(A); LMCO §155.23).
  • No sign shall be allowed if constructed or designed in a manner that may cause the sign to be confused with a traffic sign or other traffic control device, as determined by the Planning Director in consultation with the Public Works Director (LDC §8.1.6(B)).
  • No sign shall be placed in a manner visible from any public street, alley, right-of-way, sidewalk or other public easement except as provided in Chapter 8, and no sign shall be placed in or extend over a street, expressway, interstate, right-of-way, roadway, sidewalk, public or private utility or access or other easement, or alley except as provided and with approval of the Director of Public Works (LDC §8.1.8).
  • Roof signs are prohibited (LDC §8.1.9).
  • The use of pennants, streamers and balloons as signs is prohibited, except for fully inflated balloons that are 18 inches or less in size (LDC §8.1.9).
  • No sign shall be illuminated unless expressly allowed in the sign regulations (LDC §8.2.1(B)).
  • Illuminated signs are prohibited if the lighting causes glare or otherwise interferes with the vision of persons operating motor vehicles, as determined by the Director (LDC §8.2.1(B)).
  • All illuminated signs must be non‑flashing and constant in intensity and color, except as specifically allowed for changing image signs under §8.2.1(D) (LDC §8.2.1(B)).
  • Freestanding or attached signs that include changing image signs shall not be closer than 300 feet to a residentially used property or a residential zoning district, unless the property is exclusively non‑residential or the changing image sign is not visible to the residential property (LDC §8.2.1(D)(6)).
  • Freestanding or attached signs that include changing image signs shall not be located closer than 300 feet to an Olmsted Park boundary or Olmsted Parkway right‑of‑way (LDC §8.2.1(D)(8)).
  • Changing image signs with a video display method require a conditional use permit and are prohibited within the Neighborhood, Traditional Neighborhood, and Village Form Districts (LDC §8.2.1(E); note that currently such signs are not permitted at all until LDC amendments are adopted).
  • Permanent on‑premises moving signs (signs which revolve, rotate or move) are permitted only on non‑residentially used property and may not move faster than one cycle every ten seconds; such moving signs are prohibited within the Neighborhood, Traditional Neighborhood, Traditional Marketplace Corridor and Village Form Districts (LDC §8.2.1(F)).
  • No attached on‑premises sign may be mounted on any roof (LDC §8.3.3(A)(4)).
  • No freestanding sign may be located in, or project over or into, a right‑of‑way or onto adjoining property (LDC §8.3.3(B)(2)).
  • No lot frontage may have a freestanding sign unless the building on that lot is set back at least 15 feet from the street right‑of‑way line (LDC §8.3.3(B)(6)).
  • No sign regulated as a temporary sign under LMCO Chapter 155 may be placed within a public right‑of‑way, interstate right‑of‑way, expressway right‑of‑way, or public easement (LMCO §155.23).
  • No temporary sign may be constructed or placed so as to interfere with vehicular traffic by obstructing sight lines for streets, pedestrian rights‑of‑way, or driveways (LMCO §155.23).
  • No temporary signs are permitted on any property or within any development site or parkway buffer adjacent to a designated parkway or scenic corridor (LMCO §155.23).
  • Small freestanding on‑premises signs under LMCO §155.22(A) may not be placed within public or interstate/expressway rights‑of‑way or public easements unless all required permits are issued, and must be removed from those areas when the principal use is closed (LMCO §155.22(A)(3)).
  • Small freestanding on‑premises signs may not be illuminated or contain any electrical component (LMCO §155.22(A)(4)).
  • Temporary freestanding on‑premises signs may not be illuminated or contain any electrical component unless UL approved and connected to a ground fault interrupter; any illumination must be non‑flashing and constant in intensity and color; all components must be non‑moving and stationary (LMCO §155.22(C)(4)).
  • No outdoor advertising sign (billboard) may be located within 2,000 feet of the nearest edge of the right‑of‑way line of the Gene Snyder Freeway (LMCO §155.31(A)).
  • No freestanding business sign may be located within 200 feet of the nearest edge of the right‑of‑way line of the Gene Snyder Freeway; freestanding business signs between 200 and 500 feet are subject to strict size limits and must also meet applicable zoning sign size limits (LMCO §155.31(B)).
  • No small freestanding sign or banner (permanent or temporary) is permitted within 200 feet of the nearest right‑of‑way line of the Gene Snyder Freeway (LMCO §155.31(C)).
  • No sign attached to a building or structure within 200 feet of the Snyder Freeway right‑of‑way may exceed 80 square feet in area on any facade visible from the freeway, and must also meet district size limits (LMCO §155.31(D)).
  • Any sign that is insecure, in danger of falling, unsafe, installed or maintained in violation of applicable sign provisions, or erected without required permit, is deemed unlawful and must be repaired or removed upon notice; the city may remove such signs at the owner’s expense if not corrected (LMCO §§155.04(A)–(C), 155.04(B)).
  • Nonconforming permanent on‑premises signs that have been abandoned (associated principal use ceases or sign use discontinued for 360 days) must be removed; failure to remove after notice can lead to enforcement action (LDC §8.1.5(A)).

Exempt Signs in Pleasure Ridge Park

  • Signs within a ballpark, sports field or baseball diamond that are oriented toward the sports field or baseball diamond are exempt from regulation under Chapter 8 (LDC §8.1.3(A)).
  • Animating features as approved by the Planning Director are exempt from regulation under Chapter 8 (LDC §8.1.3(B)).
  • Signs required by law or constructed by a duly constituted governmental body or agency are exempt from regulation under Chapter 8 (LDC §8.1.3(C)).
  • Any sign integrated into or on a coin‑operated machine, vending machine, gasoline pump, or telephone booth is exempt from regulation under Chapter 8 (LDC §8.1.3(D)).
  • A sign carried by a person is exempt from regulation under Chapter 8 (LDC §8.1.3(E)).
  • A sign located on an operating and licensed motor vehicle is exempt from regulation under Chapter 8 (LDC §8.1.3(F)).
  • Signs listed as exempt within the Land Development Code are not required to submit plans and specifications and are not required to obtain a permit under LMCO §155.02 for erection or alteration (LMCO §155.02(A), (B)).

Sign Plan & Submission Notes for Pleasure Ridge Park

  • The term "Sign plan" is a defined term in LDC §8.1.2, indicating that sign plans are contemplated by the code, although procedural details are not included in the provided text.
  • Planned Development (PD) District sign standards must be established as part of the Master Plan for the Planned Development District and approved by the Planning Commission; the PD district master plan may supersede the general sign regulations of Chapter 8 (LDC §8.1.6(E), (I)).
  • In Suburban Workplace Form Districts, one freestanding master plan project identification sign is allowed adjacent to the primary entrance of developments with more than five lots and access from an arterial street; such master plan identification signs are in addition to the normal freestanding business signs (LDC §8.3.3(B)(10)(a)(i)).
  • In Campus Form Districts, one freestanding master plan project identification sign is allowed adjacent to the primary entrance of developments with more than five lots and access from an arterial street, and freestanding signs in multiple‑lot developments must have uniform base, side and frame design, materials and color (LDC §8.3.3(B)(10)(b)(i)–(ii)).
  • Exceptional signage (variance, waiver, or sign authorization) that does not meet current sign regulations requires review by the Sign Review Board (SRB), which conducts public hearings/meetings and makes recommendations to the Board of Zoning Adjustment or Planning Commission; this process functions as the required public review step when a variance or waiver from standard sign regulations is needed (LDC §8.4.1(A)–(D)).
  • Changing image signs with a rate of change faster than the standard limits require approval from the Planning Commission or designee after review of specified factors (LDC §8.2.1(D)(5)), which serves as a special sign approval process.
  • Changing image signs with a video display method require a conditional use permit approved by the Board of Zoning Adjustment and, once enabled by Metro Council, will be processed under the conditional use permit procedures of Chapter 4, Part 2 (LDC §8.2.1(E)).

Source: other municipal code