Questions? Call us at (262) 218-2915

Sign Regulations in Huber Heights, Ohio

Huber Heights, Ohio has specific sign regulations covering 14 sign types across 8 zoning districts. Regulated sign types include Temporary Ground Sign, Ground Sign, Wall Sign. Height restrictions apply. Permits are required for most commercial signs. Use PermitPal to get instant access to the complete regulations.

Data last verified: May 8, 2025

Need the sign code for this address?

PermitPal is an independent research tool for sign companies. We are not the city's permit office.

Sign Regulation Overview for Huber Heights, Ohio

Sample Sign Requirements in Huber Heights

Sign TypeMax HeightMax AreaSetback
Ground Sign6 ft (unless otherwise specified by location per underlying zoning ordinance)75 sq ft (unless otherwise allowed in underlying district, e.g. up to 200 sq ft for properties within 200 ft of Interstate 70/State Route 4/235)15 ft min from right-of-way (1189.05(b)); greater if required by underlying zoning ordinance
Wall SignNot listed75 sq ft per wall (total of four wall signs max per structure; collectively not exceeding 150 sq ft total)Not listed
Projecting or Suspended Sign15 ft (bottom of sign min 12 ft above sidewalk, max 3 ft above roofline)75 sq ftNot listed

* Sample data shown. Actual requirements may vary by zone. Use PermitPal for complete, location-specific regulations.

PermitPal Coverage for Huber HeightsFull Coverage

Sign Types Covered

14

  • Temporary Ground Sign
  • Ground Sign
  • Wall Sign
  • Projecting or Suspended Sign
  • +2 more types

Zoning Districts

8

Different zoning districts with specific sign regulations

Data Includes

  • Permit requirements
  • Height restrictions
  • Illumination rules

Official Resources for Huber Heights

City WebsiteMunicipal Code1 permit application link available

Frequently Asked Questions

In Huber Heights, the height limit for Ground Sign in the Multi-Family Residential Districts is 6 ft (Sec. 1189.06(b)(2)). Other zones and sign types can have different limits. Run a code check for an exact address to see the limit that applies there.

Most commercial signs in Huber Heights require a permit. From the submission notes on this page: A zoning permit shall be obtained for erection, construction, relocation or alteration of any temporary or permanent sign unless exempted by this chapter. Application is made to the Zoning Officer on a city form. Run a code check for an exact address to see the permit requirements for that zone.

Huber Heights's sign code covers 14 sign types, including Temporary Ground Sign, Ground Sign, Wall Sign, and Projecting or Suspended Sign. Most commercial signs need a permit. The ordinance lists 16 exemptions. One of them: Governmental/Community signs. The full list is on this page.

In Huber Heights, Ground Sign in the Brandt Pike Revitalization Overlay District (BP) must be set back at least 15 ft from right-of-way. The ordinance adds other placement rules for this sign type, listed in the table on this page. Setbacks for other zones and sign types can differ. Run a code check for an exact address to see the setback that applies there.

Rules in Huber Heights's sign ordinance that cover digital, changing, or flashing signs: Any electronic copy sign where different copy changes are shown on the same lamp board except as permitted under the specified section. Any sign which has intermittent lighting, moves, rotates, blinks, flashes or has spinning devices or strings of spinning devices or similar type devices except for electronic copy signs specifically permitted. Signs in Planned Unit Developments (PUDs) may be governed by a sign program that permits deviations (including number, size, setback, height, and electronic copy area) from usual requirements when approved as part of the PUD sign program. Run a code check for an exact address to see the full illumination rules for that zone.

AI-Powered Research

Ready to Research Huber Heights Sign Permits?

Stop spending hours searching through municipal codes. Enter your address and PermitPal returns the sign rules that apply to your property in Huber Heights, Ohio, with citations from the municipal code.

Need the sign code for this address?

PermitPal is an independent research tool for sign companies. We are not the city's permit office.

No credit card required · Get results in seconds

Huber Heights, Ohio Sign Rules at a Glance

Huber Heights, Ohio regulates 14 sign types across 8 zoning districts. Pendant/Suspended Signs in the B-1 (Neighborhood Business District) and other zoning districts are capped at 15 ft tall and 75 sq ft (Sec. 1189.07(d)). Most commercial signs in Huber Heights require a permit.

Detailed Sign Ordinance Requirements for Huber Heights, Ohio

Sign Rules by Zoning District in Huber Heights (8 zones)

Zoning DistrictSign Types RegulatedMax HeightMax AreaPermit Required
Brandt Pike Revitalization Overlay District (BP)7Letter copy max 18 inches in height75 sq ft (unless otherwise allowed in underlying district, e.g. up to 200 sq ft for properties within 200 ft of Interstate 70/State Route 4/235)Not listed
Single or Two-Family Residential Districts, R-1, R-2, R-3, R-4, R-4B, R-5, R-6, R-7, RMV, ES (Estate Residential), PR (Planned Residential District)25 ft6 sq ft per sign surfaceNot listed
Multi-Family Residential Districts36 ft32 sq ft per face (64 sq ft total area for double-faced sign)Not listed
A (Agricultural District), Undeveloped/Agricultural Land15 ft16 sq ft per sign surfaceNot listed
B-1 (Neighborhood Business District), B-2, B-3, Commercial Districts, PC (Planned Commercial District), O-1, Office Districts, EP (Employment Park District), I-1 (Light Industrial and Mixed Use District), I-2 (Industrial District), C, WO, PM (Planned Mixed Use District), PI (Planned Industrial District)1115 ft (to top); bottom not less than 12 ft over sidewalk75 sq ft per sign (except see interstate/arterial provisions below)Not listed
PP (Planned Public and Private Buildings and Grounds District)16 ft (unless 40 ft for interstate)75 sq ft (unless 200 sq ft per interstate rules)Not listed
PUD (Planned Unit Development Districts)1As specified by PUD sign program approvalAs specified by PUD sign program approvalNot listed
All Zoning Districts, General Regulations For All Zones13 ft within 25 ft of r.o.w.; 8 ft elsewhere2 sq ft per sideNot listed

Zone-by-Zone Sign Requirements in Huber Heights(sample of 3 of 8 zones)

Brandt Pike Revitalization Overlay District (BP)

Sign TypeMax HeightMax AreaMax WidthSetbackSigns AllowedLocationPermit RequiredPremium Details(Illumination, Size Formula, Permit Requirements, Additional Requirements, available with a free PermitPal account)Ordinance Citation
Ground Sign6 ft (unless otherwise specified by location per underlying zoning ordinance)75 sq ft (unless otherwise allowed in underlying district, e.g. up to 200 sq ft for properties within 200 ft of Interstate 70/State Route 4/235)Not listed15 ft min from right-of-way (1189.05(b)); greater if required by underlying zoning ordinanceOne per premisesSet on grade or placed on a low masonry base, landscaped beneath; must be compatible with building and streetscapeNot listedUnlockBP Overlay 1180.09(f), 1180.09; General Sign Ch 1189.07(b), 1189.05(b), 1180.07
Wall SignNot listed75 sq ft per wall (total of four wall signs max per structure; collectively not exceeding 150 sq ft total)Not listedNot listedUp to four (on structures with more than one visible side), but total sign area for all wall signs not to exceed 150 sq ft.On building façade, not above ground floor; not above one inch below second floor window line.Not listedUnlockBP Overlay 1180.09(a)-(g); Ch 1189.07(c), 1189.05(d)
Projecting or Suspended Sign15 ft (bottom of sign min 12 ft above sidewalk, max 3 ft above roofline)75 sq ftNot listedNot listedOne per individual businessAttached to building façadeNot listedUnlockBP Overlay 1180.09(b), 1189.07(d), 1189.05(c)
Awning SignNot listedSubject to same area/number limits as wall signs; only displayed in lieu of wall signNot listedNot listedOne per frontage (in lieu of wall sign)On awning; shall not project higher than top of awningNot listedUnlock1189.05(f), 1189.07(h), BP Overlay 1180.09
Temporary Ground Sign5 ft16 sq ft per sign surfaceNot listedNot allowed in public right-of-wayOne per business at a timeOn-premises, outside right-of-wayNot listedUnlock1189.07(e)-(j), 1180.09, 1189.05(j)
Sidewalk Sign (A-Frame, T-Frame)4 ft12 sq ftNot listedNot listedOne per businessWithin 5 ft of business; not to interfere with doors, wheelchair ramps, loading, or bus stops.Not listedUnlock1189.07(k), BP Overlay 1180.09
Electronic Copy SignLetter copy max 18 inches in heightUp to 50% of total wall or ground sign areaNot listedNot listedPart of allowed ground or wall signPermanent ground or wall signNot listedUnlock1189.07(j), BP Overlay 1180.09

Multi-Family Residential Districts

Sign TypeMax HeightMax AreaMax WidthSetbackSigns AllowedLocationPermit RequiredPremium Details(Illumination, Size Formula, Permit Requirements, Additional Requirements, available with a free PermitPal account)Ordinance Citation
Ground Sign6 ft32 sq ft per face (64 sq ft total area for double-faced sign)Not listedNot listedOne per complexAt entrance or frontage of complexNot listedUnlock1189.06(b)(2)
Wall SignNot listed2 sq ftNot listedNot listedNot listedOn buildingNot listedUnlock1189.06(b)(1)
Temporary Ground Sign5 ft6 sq ft per sign surfaceNot listedNot listedNot listedOn premisesNot listedUnlock1189.06(b)(3), 1189.05(j)

B-1 (Neighborhood Business District), B-2, B-3, Commercial Districts, PC (Planned Commercial District), O-1, Office Districts, EP (Employment Park District), I-1 (Light Industrial and Mixed Use District), I-2 (Industrial District), C, WO, PM (Planned Mixed Use District), PI (Planned Industrial District)

Sign TypeMax HeightMax AreaMax WidthSetbackSigns AllowedLocationPermit RequiredPremium Details(Illumination, Size Formula, Permit Requirements, Additional Requirements, available with a free PermitPal account)Ordinance Citation
Ground Sign6 ft (unless otherwise specified, such as max 40 ft for signs within 200 ft of Interstate 70/State Route 4/235, and max area 200 sq ft)75 sq ft per sign (except see interstate/arterial provisions below)Not listed15 ft from right-of-way; for interstate/State Route 4/235: 15 ft from r.o.w. and at least actual height of sign from residential propertyOne per premisesSetback at least 15 ft from right-of-way (or more per district); landscaped area beneath sign matching sign face areaNot listedUnlock1189.07(b), 1189.10(1), 1180.07
Wall SignNot listed75 sq ft per sign, four per structure max; total wall signage per structure not to exceed 150 sq ft. On lots within 200 ft of interstate/State Route 4/235, up to 200 sq ft total per structure, and no wall sign over 20% of face to which it attaches.Not listedNot listedUp to four per structure (one per visible side), total not to exceed area capOn building façadeNot listedUnlock1189.07(c), 1189.10(2), 1180.09(g)
Projecting or Suspended Sign15 ft (to top); bottom not less than 12 ft over sidewalk75 sq ftNot listedNot listedOne per businessAttached to building façadeNot listedUnlock1189.07(d), 1189.05(c)
Permanent Under Marquee SignNot listed6 sq ft per sign faceNot listedNot listedOne per businessAttached to underside of marqueeNot listedUnlock1189.07(g)
Permanent Awning SignNot listedCounted against allowed wall sign area; one per visible side of structure, max four per buildingNot listedNot listedUp to four per structure (one per visible side)Affixed to awningNot listedUnlock1189.07(h), 1189.05(f)
Pendant/Suspended Signs15 ft max75 sq ftNot listedNot listedOne per businessSuspended from buildingNot listedUnlock1189.07(d)
Temporary Ground Sign5 ft16 sq ft per sign surfaceNot listedNot in right-of-wayOne per business at a timeOn premises, not in public right-of-wayNot listedUnlock1189.07(e)
Sidewalk Sign (A-Frame, T-Frame)4 ft12 sq ftNot listedNot listedOne per businessWithin 5 ft of principal business entranceNot listedUnlock1189.07(k)

PermitPal covers all 8 zoning districts in Huber Heights. Run a code check for your exact address to get the zone that applies to your property and its full sign requirements with a free account: illumination rules, size formulas, and permit requirements for every sign type.

Run a free code check

Prohibited Signs in Huber Heights

  • Any sign or part thereof which is erected within or above a public right-of-way.
  • Any sign erected at or near any intersection of any streets in such a manner as to obstruct free and clear vision, or at any location where by reason of position, shape, or color, it may interfere with, obstruct the view of, or be confused with any Governmental/Community sign relating to traffic and safety or otherwise interfere with, mislead or confuse pedestrian or vehicular traffic.
  • Any sign mounted onto, above or incorporated into the roof of any building unless otherwise specifically permitted.
  • Any lighter-than-air, inflatable or kite-type sign or balloon situated on, attached or tethered to a premises.
  • Any sign utilizing an artificial illumination device which radiates an intensity, beam spread, glare or color which interferes with the vision of persons not located on the premises.
  • Any sign utilizing a fixed or mobile beacon, strobe light, searchlight, signaling light, spotlight or similar apparatus, equipment or device which is directed above or outside of a premises in such a manner so as to attract an unusual amount of visual attention of persons not located on the premises.
  • Any sign or part thereof which utilizes flame.
  • Any electronic copy sign where different copy changes are shown on the same lamp board except as permitted under the specified section.
  • Any sign which conveys visual information that is obscene.
  • Any sign which has intermittent lighting, moves, rotates, blinks, flashes or has spinning devices or strings of spinning devices or similar type devices except for electronic copy signs specifically permitted.
  • All banners, except as specified in the code, streamers, pennants, strings and spinning devices.
  • Portable signs with a commercial message, except as authorized under temporary signs.
  • Commercial message signs located off-premises from the particular business advertised.
  • Signs with a commercial message that are painted on or attached to a stationary vehicle or trailer which is located in such a manner as to serve exclusively as permanent, temporary, or portable signage.
  • Deteriorated signs.
  • Any sign or graphic (canopy, above-ground wall, flashing/intermittent/moving lights) not in conformance with the sign and lighting standards of the overlay and general code.
  • No temporary sign, bandit sign or snipe sign shall be placed upon any utility or street sign pole or upon any public right-of-way.
  • No sign shall be located in such a manner as to be primarily viewed from residential property (for business, industrial or nonresidential zoning districts).
  • Wall signs are prohibited above the ground floor level or above a height of one inch below the second floor window line, whichever is lower (in BP overlay).
  • Canopies designed as signs are prohibited (in BP overlay).
  • No flashing or intermittent or moving lights shall be permitted, either freestanding, attached to a facade, or as a part of an approved sign (in BP overlay).

Exempt Signs in Huber Heights

  • Governmental/Community signs.
  • Temporary window signs constructed of paper, cloth or similar expendable material, including signs located inside a structure (with further limits for permanent painted or affixed signs).
  • Hazard and Prohibition Signs and 'No Trespassing', 'No Parking', and other similar warning signs.
  • Holiday decorations that do not contain a commercial message.
  • Internal signs (not intended to be viewed from public streets and not visible from public street or adjoining properties).
  • Official Federal, State or local government flags.
  • Human signs outside of the public right-of-way or on a City sidewalk (subject to certain distance and safety requirements; not within three feet of an ingress or egress on a sidewalk).
  • Routine maintenance and in-kind replacement of materials, except for the replacement of graphics (BP overlay).
  • Properties used solely for one or two family residential purposes are exempt from BP overlay standards.
  • Signs that may be displayed pursuant to the provisions of the chapter may contain a non-commercial message.
  • Snipe signs and Bandit signs do not require permits.
  • Roadway lighting required by the appropriate public agency for health, safety and welfare purposes (for lighting standards).
  • Lighting approved by the City as part of construction (for lighting standards).
  • Flag lighting, provided that the illumination is the minimum level necessary, and that the light source is aimed and shielded to direct light only onto the intended target and to prevent glare for motorists and pedestrians (for lighting standards).
  • Emergency lighting approved by the City, provided the lighting is discontinued upon the abatement of the emergency necessitating said lighting (for lighting standards).
  • Other temporary lighting determined to be reasonable and appropriate by the City (for lighting standards).

Sign Plan & Submission Notes for Huber Heights

  • Signs and graphics must conform to Chapter 1189 of the City of Huber Heights Planning & Zoning Code and, where in the Brandt Pike Revitalization Overlay, must also conform to additional overlay requirements.
  • A zoning permit shall be obtained for erection, construction, relocation or alteration of any temporary or permanent sign unless exempted by this chapter. Application is made to the Zoning Officer on a city form.
  • Requests for variances from provisions of the sign chapter are permitted subject to the requirements and limitations set forth in Section 1127.03(c).
  • Signs in Planned Unit Developments (PUDs) may be governed by a sign program that permits deviations (including number, size, setback, height, and electronic copy area) from usual requirements when approved as part of the PUD sign program.
  • For developments within a planned unit development district, approval of signage (including exposed neon or similar tube lighting) may be through the Planning Commission.
  • BP Overlay: In addition to conformance with Chapter 1189, all signs and graphics must meet additional standards specified for the Brandt Pike Overlay.
  • All development, including signage, within the BP Overlay is subject to the procedures and provisions set forth in Chapter 1180, including conditional use application/approval.
  • Major changes to a PUD landscape/sign plan or alternative compliance require submittal and approval of a revised plan through the appropriate process.
  • Snipe signs and Bandit signs do not require permits, but are still regulated by duration limits.
  • When site plan or zoning permit approval is required, exterior lighting (including sign lighting) must be reviewed and approved as part of the approval process and must conform to lighting standards (1181.21).

Source: municode municipal code